Posts: 453
Threads: 59
Joined: Dec 2008
Hi All,
In making the carshop i need to know the depth of inspection pits typical of such a service facility ........ a search on the net ranges from 4ft - 7ft deep ... is there a common depth for most of these types of pits could anyone tell me please.
The height from the rail top to the pits base.
Also what types of other items are around the shop ?
Posts: 496
Threads: 22
Joined: Dec 2008
If the pits included with the Walthers roundhouse are correct, I'd say about 4'. I built an outdoor pit and used stairs by, umm, can't think of who right now. Maybe Pikestuff? Anyway, I just used sheet styrene cut to match the steps and I just measured the depth, 4', close to the Walthers. A couple pics, ground cover to come soon.
Posts: 410
Threads: 17
Joined: Dec 2008
If you are modeling a somewhat modern facility, here's an idea I got photos of of a car & locomotive shop in Jamaica. This is an outdoor inspection facility for cars and engines.
Might be an idea worth exploring. They are 5' deep. The large yellow pole to the right is a 5 ton capacity L Shaped Jib Crane with remote.
I think this shop and inspection facility is what I'll use for an idea on my layout. Might be worth considering for yours.
Tom Carter
Railroad Training Services
Railroad Trainers & Consultants
Stockton, CA
<!-- m --><a class="postlink" href="http://www.railroadtrainingservices.com">http://www.railroadtrainingservices.com</a><!-- m -->
<!-- e --><a href="mailto:tomwcarter@railroadtrainingservices.com">tomwcarter@railroadtrainingservices.com</a><!-- e -->
Posts: 453
Threads: 59
Joined: Dec 2008
Hi jglfan, Tom,
Many thanks for the great pics
they will hlep a lot for details
The pits are inside this car repairshop from walthers
Here is the base ready for the inner walls of the pits
Posts: 2,429
Threads: 63
Joined: Dec 2008
Well, someone standing in the pit has to be able to reach the underside of the loco without standing on anything. How far up they have to reach would depend on the locos in question and which bits might need attention. My own feelings is 7 feet to an axle from the bottom, but I've never been down one.
Besides Walthers, models are available from Chooch and Peco.
David
Moderato ma non troppo
Perth & Exeter Railway Company
Esquesing & Chinguacousy Radial Railway
In model railroading, there are between six and two hundred ways of performing a given task.
Most modellers can get two of them to work.
Posts: 989
Threads: 55
Joined: Dec 2008
That's a really nice idea to model...something you don't see everyday.
Mark
Citation Latitude Captain
--and--
Lt Colonel, USAF (Retired)
Posts: 4,161
Threads: 174
Joined: Dec 2008
This a great thread! Pits make such an interesting detail!
Ralph
Posts: 335
Threads: 27
Joined: Dec 2008
BR60103 Wrote:Well, someone standing in the pit has to be able to reach the underside of the loco without standing on anything. How far up they have to reach would depend on the locos in question and which bits might need attention. My own feelings is 7 feet to an axle from the bottom, but I've never been down one.
Besides Walthers, models are available from Chooch and Peco.
I've been in one, but it was when I was a kid - and it was deep then!
Another source is Diamond Scale:
<!-- m --><a class="postlink" href="http://www.diamond-scale.com/products__engine_service_pits_platforms.htm">http://www.diamond-scale.com/products__ ... tforms.htm</a><!-- m -->
Matt
Matt Goodman
Columbus, Ohio
Posts: 1,088
Threads: 116
Joined: Jan 2009
looking at old photos of roundhouse pits I'd say 7 ft would be close.
Jim