Steamtrains' 2010 Summer structure challenge entry - Printable Version +- (https://bigbluetrains.com) +-- Forum: Photographer's right of way (https://bigbluetrains.com/forumdisplay.php?fid=37) +--- Forum: Contests & Challenges (https://bigbluetrains.com/forumdisplay.php?fid=9) +--- Thread: Steamtrains' 2010 Summer structure challenge entry (/showthread.php?tid=2773) |
Re: Steamtrains' 2010 Summer structure challenge entry - Steamtrains - 08-09-2010 That might work..!! And maybe a hidden camera to record every movement, and......Nahh...That ain't gonna work.... Re: Steamtrains' 2010 Summer structure challenge entry - Steamtrains - 08-12-2010 Just a quick update... Started work on the roof (finally)...I approached it somewhat differently from how a roof is normally built...I 'm building it "backwards", starting with the sheeting, and will finish with the framework....You can do that with a model... OK...Here's the 1/16" roof "blank" with the fascia and soffit being fitted... And a close-up... Working with that itsy-bitsy fascia trim was a real joy..!!...Not to mention all the angle cuts... The roof framing will come next, the chimeneys, staining & weathering, as well as the tar-paper sheeting. Now it's beginning to look like something....but still a ways to go... Re: Steamtrains' 2010 Summer structure challenge entry - Gary S - 08-12-2010 Steamtrains Wrote:Now it's beginning to look like something... I'll say. It is looking great! Re: Steamtrains' 2010 Summer structure challenge entry - Steamtrains - 08-13-2010 Some more.... Thanks for your commment, Gary...I can always count on you to check my stuff out... Here's the "porch" roof under construction. I used 1/64" ply for the decking or it wouldn't clear the clerestory windows on the front . And a couple of pics of the almost-finished structure... The supports for the "porch" won't be put in until the structure is ready for placement on the layout...Don't want those flimsy supports breaking off while messing with it.... Stay tuned...More to come.... Re: Steamtrains' 2010 Summer structure challenge entry - Gary S - 08-14-2010 Steamtrains Wrote:Thanks for your commment, Gary...I can always count on you to check my stuff out... I may not always have "meaty" thoughts about the subject, but I figure the least I can do is let people know that I am looking at their stuff and appreciate the photos. Also, I learn alot by following along with the construction. Your roundhouse is shaping up well, and I can envision it on your layout, surrounded by some railroad equipment and junk, some scenery in the background, and a loco or two hanging about. It's gonna make a pretty scene for sure. Re: Steamtrains' 2010 Summer structure challenge entry - nachoman - 08-14-2010 Some good ideas an inspiration in this thread - perhaps enough to get me off my rear-end today! Re: Steamtrains' 2010 Summer structure challenge entry - Ralph - 08-14-2010 That is turning out VERY nicely! Ralph Re: Steamtrains' 2010 Summer structure challenge entry - Steamtrains - 08-14-2010 Thanks guys....Any excuse is good to get off one's butt and "play" with trains.. Currently working on the smoke stacks and hoods. Hopefully I'll have them finished this weekend (more like Monday.. ), and then it'll be roofing time.... BTW...Anybody have any idea on how to make the shrouds on the smoke stacks..?? Re: Steamtrains' 2010 Summer structure challenge entry - Gary S - 08-14-2010 Cone shaped shrouds? Re: Steamtrains' 2010 Summer structure challenge entry - Steamtrains - 08-14-2010 Yup.... Re: Steamtrains' 2010 Summer structure challenge entry - Gary S - 08-14-2010 Take thin sheet styrene, the thinner the better. Draw a circle which is 25 percent larger than the desired diameter of the bottom of the shroud and cut it out. Then cut a small pie shaped piece out of the circle. Then pull the two cut ends around togehter. This should form a cone. Now, going by what you came out with, trial and error will dtermine if you need to make the original circle bigger, and what size the pie pieces need to be to make what you want. Re: Steamtrains' 2010 Summer structure challenge entry - nachoman - 08-14-2010 Gary S Wrote:Now, going by what you came out with, trial and error will dtermine if you need to make the original circle bigger, and what size the pie pieces need to be to make what you want. You could use paper for your "trials" to save wasting styrene. Another thought could be pastry bag tips. I see those all the time at thrift stores. Re: Steamtrains' 2010 Summer structure challenge entry - Gary S - 08-14-2010 nachoman Wrote:You could use paper for your "trials" to save wasting styrene. Doh! :oops: Yes, definitely use paper first! Re: Steamtrains' 2010 Summer structure challenge entry - Steamtrains - 08-14-2010 OK...I'll give that a try...Thanks. Update....It works...!!! And I note that the size of the wedge determines the "coneniness" (yes, that IS a word... ) of the cone.... Re: Steamtrains' 2010 Summer structure challenge entry - Gary S - 08-14-2010 Alright Gus! I was finally able to give some advice that is of use! |