Big Blue has inspired some purchases
Good to see that this thread is progressing nicely beyond my own empire! (Glad to see that reading posts on this site is infecting others in similar ways) Great caboose kitbashing going on, Tom and Matt... Can't wait to see the progress.

On another note, my son's subdivision abuts the BNSF running from Temple, TX to Lampassas and further northwest into New Mexico. I had his dogs out daily throughout the week in an attempt to do a little railfanning, but the frequent trains weren't running with me and the dogs. I do like the new BNSF orange/black/yellow scheme.... (NO!!!!!! - attempting to rain in my potential to buy more projects).
Check out my "Rainbows in the Gorge" website: http://morristhemoosetm.wixsite.com/rainbows
Reply
A short update on my CR patched LVRR unit.  The thing had been sputtering and duttering around my layout.  Ran, stopped, ran, slowed down, stopped.  Light sputtered.  Took her apart and looked at connections to the wheels which still looked good and tight.  Tried cleaning up portions of the track that were more tempermental than others - still sputtered.  Then I took a good look at the wheels themselves.  Wouldn't you know it, they were quite dirty.  Ran the Dremel with a wire wheel over each wheel and she is now running like a champ.  It's the little things sometimes!  I think I'll weather it this weekend and add couplers - as much as I like the paint job, it needs to fit into the fleet!

So, here's the prototype beaten look I'm working toward...

CR_5487_1536x864-1024x576-1160x665.jpg (1160×665)
Check out my "Rainbows in the Gorge" website: http://morristhemoosetm.wixsite.com/rainbows
Reply
Goosed into action I got the paints and the washes out.  I still need to do a bit more on the areas underneath the shell, but here's my first approximation of the prototype photo.  I also need to find the coupler bodies that came off of this Roundhouse chassis...  I may have to do some work to fit the coupler pockets in this one.

   
Check out my "Rainbows in the Gorge" website: http://morristhemoosetm.wixsite.com/rainbows
Reply
I've found that eyeglass cleaners are useful as wheel cleaners. These are little cloth-like sheets that my wife buys, maybe 2"x5". After using on the glasses, they are still good but dry out. I put a bit of track cleaning liquid on it and pull it across the rails so that the liquid is over the rails. Then run the loco onto it and spin the wheels in the solution. It may not work as well if pickup is one rail on one truck.

It always seems a shame to throw them out when they still look pristine (well, I don't get anything that filthy on my glasses.)
David
Moderato ma non troppo
Perth & Exeter Railway Company
Esquesing & Chinguacousy Radial Railway
In model railroading, there are between six and two hundred ways of performing a given task.
Most modellers can get two of them to work.
Reply
Two of the three new purchases I have made and they will fit perfectly into the 1980's Conrail

Atlas C30-7 #6609. There is some work that needs done to bring this locomotive up to how it was on Conrail. Parts are already ordered.
   

Atlas U36C #6895. There is also some work that needs done to bring this locomotive as well.
   


They are both DCC ready which I found out after removing the shells and seen the dummy plugs for the computer boards. I am not 100% sure which DCC maker it is so any help from you guys would be awesome. Then I can go and get the plug and a DCC system. 

I have run both of these locomotives and they run nice and smooth. I did try to mate them together and the C30-7 pulled the U36C so they will need speed matched in the future.

The third locomotive isn't pictured yet but I did get in contact with Bruce and nabbed up the Conrail GP15-1 he had for sale on here.
Matt
Conrail's Blairsville Cutoff 
Reply
(11-12-2026, 01:29 PM)LiveSteamer Wrote: They are both DCC ready which I found out after removing the shells and seen the dummy plugs for the computer boards. I am not 100% sure which DCC maker it is so any help from you guys would be awesome. Then I can go and get the plug and a DCC system. 

Matt, if the plug is there any brand decoder should work. basically depends on how many functions you want. for non sound units i lately have been using digitrax DZ123PS which is small and just plugs in. it only has front and rear lights but that is all I use on most of my locomotives. Shop around and find them for less tham 20 bucks. decoder
As for system I like the MRC Prodigy advance squared but the NCE and Digitrax are good systems too. If you add a wifi adapter you can run the trains with your phone. 
Charlie
Reply
(11-12-2026, 04:36 PM)Charlie B Wrote:
(11-12-2026, 01:29 PM)LiveSteamer Wrote: They are both DCC ready which I found out after removing the shells and seen the dummy plugs for the computer boards. I am not 100% sure which DCC maker it is so any help from you guys would be awesome. Then I can go and get the plug and a DCC system. 

Matt, if the plug is there any brand decoder should work. basically depends on how many functions you want. for non sound units i lately have been using digitrax DZ123PS which is small and just plugs in. it only has front and rear lights but that is all I use on most of my locomotives. Shop around and find them for less tham 20 bucks. decoder
As for system I like the MRC Prodigy advance squared but the NCE and Digitrax are good systems too. If you add a wifi adapter you can run the trains with your phone. 
Charlie

Matt, 

   I also run with an MRC Prodigy (the Express (squared)) combined with an MRC booster unit (a Power Station 8 which brings up my current capacity from about 1.6 amps (enough to run 3 locos consisted at full speed) to over 8 amps (roughly 16 locos simultaneously)), and if you're on the lookout, you can find these occasionally at a good price.  For comparison, Charlie's Prodigy Advanced (squared) provides 3.5 amps by itself without a booster, but the price is higher than my Express.  Lenz, TCS and Digitrax also make good dependable DCC systems which both get better reviews (generally) than MRC, but you'll probably have to shell out more money.  With model railroaders dying off or giving up on the hobby, if you're patient, you should be able to pick up something used that will work.

Another option is to run your purchased locos in analog mode - they should probably have been sent to you with an adapter that plugs into the DCC plug until you decide on an appropriate DCC system that works for you and your layout.  

I'm in agreement with Charlie on decoders - most should work with your plug (I'm assuming an 8-pin in those Atlas units (newer DCC ready use a 22-pin plug which allows for greater function programming)).  You do want to make sure the decoder you order has the capabilities you're looking for, since DCC providers offer stationary decoders (to control turnouts or layout lighting, mobile (locomotive) decoders without sound, and mobile decoders with sound).  As you increase in capability, so do the prices of each, with sound decoders roughly doubling in price over the non-sound decoders.  Mobile decoders are also rated by scale - sometimes you can get away with an N-gauge decoder in an HO locomotive, but you're probably asking for trouble.  Like Charlie, I'm also a fan of Digitrax decoders.  If you need more functions than 2 (directional lighting control, front and rear lights), the Digitrax decoder models with a "4" or a "6" in their catalog number (instead of the 2 in the DZ123PS) will provide the capability to add things like ditch lights, strobe lighting, classification lighting, etc.

Once you do find the right decoder, you'll find that for the 8-pin plugs, it is possible to plug the decoder in two different ways - pay attention to the correct orientation for right and left side track that the decoder manual will provide, and you should then have appropriate forward, reverse, and front and rear lighting functions.  It's then possible to change the polarity of the entire loco by altering some Control Variables (CVs) in order to run that locomotive "backward" in a consist.  You can also change how fast the locomotive accelerates, decelerates, what the maximum speed will be, etc.  A whole new world opens up for exploration (full of pros AND cons...).
Check out my "Rainbows in the Gorge" website: http://morristhemoosetm.wixsite.com/rainbows
Reply
Thank you guys. I will look into everything. This is a first for me and I was against DCC for the longest time but if I want to run more than one locomotive and not fry a controller, I guess taking the dive to DCC is the best option.
Matt
Conrail's Blairsville Cutoff 
Reply


Forum Jump:


Users browsing this thread: 6 Guest(s)