Remaking of the Ridley Keystone & Mountain
When I put down the split roadbed, I had big pins where the middle of the track would go. You have little pins in there. Then I could butt the roadbed halves right against them.
David
Moderato ma non troppo
Perth & Exeter Railway Company
Esquesing & Chinguacousy Radial Railway
In model railroading, there are between six and two hundred ways of performing a given task.
Most modellers can get two of them to work.
Reply
I finally found the time to work again on the layout.

I placed the foam roadbed in the area where I am going to do scenery. I laid the track back over the roadbed to make sure everything fits.

[Image: 3humZUV.jpg]

[Image: UBQAIn0.jpg]

[Image: 33QRRpi.jpg]

Looking the other way.

[Image: pHakXDG.jpg]

[Image: EXdAgms.jpg]

I am using Woodland Scenics foam roadbed. I will eventually cut around the turnouts when I finalize those areas. Where there is no paint the roadbed is temporary,

Using Woodland Scenics transition sections I added 2% temporary transitions from the foam board to the foam roadbed.

[Image: RmLrBBU.jpg]

[Image: H0eD8na.jpg]

Test trains have been successfully run through the section. I plan on doing one or two run by trains. After that I will glue the roadbed in place in the area where the passenger station will go.
Tom
Silence is golden but Duct tape is silver
Ridley Keystone & Mountain Railroad
My Rail Images Gallery
Reply
Lots of progress, looking good....You have more track down than I have total space.
Don (ezdays) Day
Board administrator and
founder of the CANYON STATE RAILROAD
Reply
Coming along nicely Tom. I am looking forward to seeing it finished.
Charlie
Reply
(11-11-2021, 07:06 AM)Charlie B Wrote: Coming along nicely Tom. I am looking forward to seeing it finished.
Charlie

Is a layout ever really finished? Misngth Goldth
Tom
Silence is golden but Duct tape is silver
Ridley Keystone & Mountain Railroad
My Rail Images Gallery
Reply
Started gluing down the roadbed. Working on the inside track first.

[Image: ZlKi4wm.jpg]

[Image: YJoAv1i.jpg]

[Image: VxG66BD.jpg]

Need to run to the hardware store and grab some Liquid Nails or something similar for attaching the track.
Tom
Silence is golden but Duct tape is silver
Ridley Keystone & Mountain Railroad
My Rail Images Gallery
Reply
Keep up the excellent work Tom,the track plan looks great---all your hard work will be worth the effort.
Reply
(11-18-2021, 10:16 PM)tompm Wrote:
(11-11-2021, 07:06 AM)Charlie B Wrote: Coming along nicely Tom. I am looking forward to seeing it finished.
Charlie

Is a layout ever really finished? Misngth Goldth

A model railroad may be complete, but never finished.
David
Moderato ma non troppo
Perth & Exeter Railway Company
Esquesing & Chinguacousy Radial Railway
In model railroading, there are between six and two hundred ways of performing a given task.
Most modellers can get two of them to work.
Reply
Using Liquid Nails and a putty knife to spread out the Liquid Nails I attached the inside track.

[Image: deOjFbi.jpg]

[Image: ARnooWc.jpg]

Next I moved on to gluing down the roadbed for the outside track

[Image: qvpI8JI.jpg]

[Image: 67pvhVg.jpg]

Then attaching the outside track. In progress photos.

[Image: BwlOiOz.jpg]

[Image: kjdijvl.jpg]

Finished attached track

[Image: Q4gaAcj.jpg]

[Image: VOt3eGd.jpg]

Ran some test trains and time to move to next step.
Tom
Silence is golden but Duct tape is silver
Ridley Keystone & Mountain Railroad
My Rail Images Gallery
Reply
The next step is weathering the track.

For this I am trying something new. I am using Woodland Scenics Tidy Track Painter Pen. For the side of the rails I am using Rusty Rail and for the ties Weathered Tie.

First section I tried with both the rail and ties weathered.

[Image: Rr39367.jpg]

Next is a section where just the rails are done alongside an untouch section.

[Image: idDhG9n.jpg]

Here is a section with both the rails and ties done against an undone section

[Image: BqA2RmA.jpg]

Lastly an overhead shot showing the weathered track on top and unweathered below.

[Image: pjJRTvF.jpg]
Tom
Silence is golden but Duct tape is silver
Ridley Keystone & Mountain Railroad
My Rail Images Gallery
Reply
I read an article in a recent Model Railroader that talked about making foundations for structures as a way to make them fit better into the scenry. After thinking about it and knowing I need to raise the passenger platforms I decided to give it a try. The article recommended three materilas to choose from; wood strips, foam board, and plaster with or without a facade. For my purpose I chose the foam board.

Using the base of the platforms I traced the outline and cut the foam board. The type of board I chose required two layers as you can see.
[Image: aQ26Yy5.jpg]

Since there are four platforms I had to cut a total of eight pieces.
[Image: 2DsEDgi.jpg]

I had to cut out for the stairs in two of the platforms.
[Image: jjbbbWc.jpg]

I placed the boards and the platforms and checked the height against a passenger coach.
[Image: KKbiXne.jpg]

Checked to make sure the cus for the stairs were done correctly. When the foundations are in place I will use scrap to fill in the gap.
[Image: vnVt8kJ.jpg]

The platforms are too far from the rail. The little plastic people would have quite a jump to board. Therefore I have to remove some of the roadbed edge.
[Image: 9VQkuML.jpg]

All the roadbed edge removed for the platforms.
[Image: CQucKbA.jpg]

[Image: z22aXTZ.jpg]

Test of the platform location.
[Image: hDXZrzM.jpg]

Next I need to paint the foam board black. I also need to figure out a way to keep the ballast out of the area of the foundations. I don't want to set the foundations until the blalast is in place as I don't want it spiling onto the foundation and creating problems with setting the platforms.
Tom
Silence is golden but Duct tape is silver
Ridley Keystone & Mountain Railroad
My Rail Images Gallery
Reply
Very nice, Tom! Love to see your progress on this, Great job! Applause Applause Icon_e_biggrin
[Image: sig2.jpg]-Deano
[Image: up_turb10k_r.gif]
Reply
Agree with Deano, nice job, like the fact that you have the room to do this.
Don (ezdays) Day
Board administrator and
founder of the CANYON STATE RAILROAD
Reply
Thanks guys!

I finally got to the ballasting. Here is the inside track. The wood is preventng the ballast from getting into the area where the station platforms will go. Shot taken not longer after the glue mixture was applied.

[Image: 3kRfex3.jpg]

[Image: AN9AzLs.jpg]

Glue has dried and wood is removed.

[Image: rhhHJHP.jpg]

[Image: MTKMMIr.jpg]

The outside track track's turn

[Image: rBCRFhK.jpg]

[Image: DLmvSUp.jpg]

Outside track after the glue dried.

[Image: MiH1IJK.jpg]

[Image: jgDyL7B.jpg]

Next up is placing the station platform foundations.
Tom
Silence is golden but Duct tape is silver
Ridley Keystone & Mountain Railroad
My Rail Images Gallery
Reply
Coming along very nicely, Tom Applause Applause  I cant wait to see the platforms and station set in Icon_e_biggrin , it will make a BIG impact on that area Applause
[Image: sig2.jpg]-Deano
[Image: up_turb10k_r.gif]
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)