Shore River's SW1500 does some switching at the Mannheim Yard.

Bruce

Attached Files

Thumbnail(s)
   

I've seen a layout - may well be O gauge - with photos of it set up on picnic tables at an exhibition - I thought I had a link to it but it may have gone when my previous computer crashed -it was a small country switching yard and the trackplan was something like this. There were several detail photos as well. Please help me to prove I'm not yet going completely round the twist !

   

I'm very fond of little critturs and when I found this one I had to order it. Well,it's arrived now and first impressions are very good. I didn't realise it would be a whitemetal kit but that's to it's advantage. I estimated the wheelbase at 24.5 mm and ordered a Tenshodo Spud with 10.5 mm wheels on the strength of it. Both arrived together and I was pleased to find the the Spud is perfect for it. The axle ends will have to be cut,but apart from that and modding the pickups for DCC it'll be good to go. I'll also have to figure out what Kadee's will fit. This will be fun. On the layout itself, I have a big problem in that the sector plate is far too short. A bit of a re-think there is needed.

Any one have a reliable source for resistors to make resistor wheels for block detection? My club is soon going to require that all rolling stock should have them but I need to do a couple of cabin cars right now. I know the value should be 10K for single axle application, but not sure of other specs, tolerance, or power rating. Please fill in the blanks if the later 2 specs are important.


Thanks,

Mark

Probably already answered somewhere, but can bulk foodstuffs like corn oil and flour be unloaded at a team track? I'm wondering if there are FDA rules about that - possible contamination, uncovered facility, etc. I'm not talking about a dedicated transload but a vanilla spur.

Thanks!

A short time ago I have written here in Big Blue about my newly purchased Norfolk & Western caboose of class CG, a model that should pull my freight train of the Thirties with my M2 loco of N&W.



I was sure that I had done a good deal with this model which was built by Ajin in South Korea and was imported by Overland Inc. - however I was very disappointed! It's looking well detailed however this was only the first impression. Look the problems please, which I found on the model.

Yes it's correct, the first impressions were good - however this was the first problem, the model is a very bad runner! However I searched for pictures and a great source are the archives of N&W Historical Society, where I found a lot of documents and pictures about this class CG caboose (and also a lot of differences at this model). I'm planning to use this model with a 1930 train so I will install the more correct Bettendorf trucks of that time with leaf springs and so all running problems should be eliminated. Two different truck types are ordered, Tichy Bettendorf trucks with leaf springs and Kadee self-centering caboose trucks. All pictures shows that these cabooses were equipped with these trucks. Maybe that the cabooses received these swing-motion trucks in later years, however I do not need them. With this the first problem is solved however this was one of simplest one!
A few more checking showed on underside an AB-brake however with a lot of not fixed connections at brake gear, a fat hole for a missing part and some more incomplete details.



Here the most noticeable mistakes.



A free hanging rod and open holes at levers of brake gear.



A pull rod to hand brake with sharp bends (!) and missing connections to the both hand brake shafts at platforms.



The most noticeable mistake is visible at left lever which has been cut off by a plier in order to give the truck enough play! However which relative short car needs such a spin for the trucks?
The hole is prepared for fixing a sink which I found in a parts bag, however a fitting screw was not inserted. Also I had to search a well fitting screw and I think that I have a lot of different screws. I don't understand because the sink was not fixed to model?



The more closer you look at the model, the more defects you will discover! See bolsters and cross beams here - nothing more than the cover sheets!
However this is not all! The real troubles became visible as I checked and compared this model with the drawings of archives of NWHS - here a link to a related search.
Unfortunately I can't show these drawings here in this post because of restricted permission rights. However you can see these related blue prints on a gallery of my website. I was very interested to study these documents in a high resolution version and so I ordered them for private use on my website by paying a small fee to NWHS. The result was very surprisingly!

I found on documents of this class CG caboose underbody arrangements with a K-brake and also with an AB-brake, however with a very different arrangement! Exactly this underbody arrangement which was built to the model was to find on two different caboose classes, the CH class and the C2 class. Used the producer here an underbody of other caboose models which he produced also? Unfortunately I can't give an answer on this question, however I know that this underbody is wrong! Maybe that the N&W modified brakes in later years how brakes must be changed from K-Brakes into AB-brakes after restrictions of AAR for K-brakes? However definitively ist this model with this brake is not that what I would like to use for my 1930 train! At this time the cabooses of CG class were equipped with the original in 1927 built K-brake!

There were only one conclusion together with all the mistakes of the underbody of my model - I must remove all the brake components and construct a complete new brake, a K-brake of course and maybe exactly built after the blue prints. And about this I will write in next post.

I've just aquired one of these beasties and intend to convert it to DCC. Took it apart to see what's involved and found that it's split frame. Don't see any big problems there. However, I would like to fit a Loksound chip and don't know what engines these had. I assume it to be a 6 cyl. lump of the Caterpillar family . Any one know please?

Just came accross these details for Ho scale modern buildings.<!-- m --><a class="postlink" href="https://www.shapeways.com/shops/sneumann">https://www.shapeways.com/shops/sneumann</a><!-- m --> I ordered 3 sets of the Lighting fixtures and camera.pretty cool stuff i think,just add Leds and i'm off to a good start for all my Industrial buildings Also ordered some Factory stairs from this guy <!-- m --><a class="postlink" href="https://www.shapeways.com/shops/rsprague">https://www.shapeways.com/shops/rsprague</a><!-- m -->

I have a Bachmann GP 9 fitted with a Loksound chip and wish to fit ditch lights. Is it easy to do and can a supplier be reccommended? Thanks.

It's beginning tomorrow!!!!!

Model Railroad Open Houses DE - MD - PA - NJ

<!-- m --><a class="postlink" href="http://www.modelrailroadopenhouse.com/modelschedule.html">http://www.modelrailroadopenhouse.com/m ... edule.html</a><!-- m -->

If you are in the area, I recommend almost evry layout!!! They are all fantastic in their own way!
~~~~~ Even the abNormally small ones